Johnson Controls 7700 Low Volume (Non-Relay) Electro-Pneumatic Transducer

E-P TRANSDUCER; 0-10V; LO-VOL REPLACES PC-3001-1

Our 7700 low volume (non-relay) electro-pneumatic transducer is designed to replace the PC-3001-1 and PC-3001-2. Key features include: Stainless steel construction, Shaft length 2.0 inches (51mm), Dual voltage (30V DC/5V AC), Non-relay circuitry, Special mounting holes for quick and easy installation, Weight: 1.3 lbs. (590 grams)

The new JCI 7700 Series is a line of non-relay electro-pneumatic transducers designed for many different, but popular, pneumatic output applications. All transducers in the JCI 7700 Series have large, easy to read bar graph scales, an over travel indicator and pre-wired leads to eliminate wiring errors. These features make any of these transducers a must have for anyone who has ever installed an e-p relay or wants a higher quality product at a lower cost of ownership. This product is a direct replacement for the PC-3001-1 pneumatic pressure transdu

This NEMA 4X electro-pneumatic transducer will replace the Relay Valve P/N PC-3001-1. The 7700 series transducers are mounted in Johnson Controls' DS480, DSC600, DSC800, DSC2560, DSC6000, DSC6200 control panels for high volume applications where high reliability is needed. They are used in Air Movement & Control equipment to close limit or limit & temperature control valves to control temperature or position in response to inputs from temperature or pressure sensors located in the conditioned space.

The Low Volume (Non-Relay) Electro-Pneumatic Transducer features a 5 mL volume and is intended for use as a transmitter or receiver in an electro-pneumatic transducer system. This transducer is designed to switch control air pressure, and must be used with a Johnson Controls pneumatic actuator that operates on a switching cycle. It switches from full open to full close, or from full close to full open, according to the output of a 0-10 VDC control signal.

A Johnson Controls 7,700 low volume (non-relay), electro-pneumatic transducer with a 0-10V output and a 10 psi to 40 psi range, with an operating frequency of 1 KHz and a mounting flange.

The Johnson Controls 7700 Low Volume Electro-Pneumatic Transducer is designed for use on fire protection systems. This part is compatible with Type 1, X, R, and low temperature detectors. It is also compatible with both single and three-element BOV's, type V or K temperature sensors, and with the 7110 low volume relay. This transducer has a 21/2 inch body length and comes with a 5/8-14 male thread connection.

The 7700 Low Volume (Non-Relay) Electro-Pneumatic Transducer is a precision instrument designed to measure or control pressure in vacuum tubes, vacuum systems, pneumatic systems, and air filtration systems.

The Johnson Controls 7700 Low Volume (Non-Relay) electro-pneumatic transducer is designed to meet the tight specifications of low volume commercial vehicle applications. This transducer features uniquely shaped diaphragms that minimize the delivery area, preventing the bumping of side seals. Features include interchangeable force chamber assembly and three-dimensional spring mass system that allow you to customize for specific applications.Saftronics models include correct sensing linkages, electrical connectors, preinstalled sensing element, and wiring harness.

The 7700 Low Volume (Non-Relay) Electro-Pneumatic Transducer monitors the pressure level of a fluid and transmits that signal to a controller or other pneumatic device. It offers the same high performance of our 7700 series, but in a smaller body with minimal dead space.

The Johnson Controls 7700 Low Volume (non-relay) electro-pneumatic transducer is a low-volume alarm designed single or dual zone muting for systems that provide 24VDC power.

Electro-pneumatic transducer of compact design. A fixed piston with a 3 mm

Johnson Controls' Low Volume ComfoTrac ComfoStat actuators offer a low-volume option for HVAC applications. They have a wide output range of 0 to 10 VDC at non-relay flow rates from 1 – 100% that can replace 80 – 500 cfm, 1 – 10 WPC, ? – 1 HP motors, and 0 – 15 ft3/min blowers.