Johnson Controls V-3000-8012 Pneumatic Valve Actuator, 3 to 13 Spring

"8"" EXPOSED PNEUM ACT 25# MAX"

Johnson Controls V-3000-8012 Pneumatic Valve Actuator . 3 to 13 spring, mounting; 6" mounting; 6"" stroke; 6"" max act travel; pneumatic; pressure min, psig min 0.5, max 0.5; psi maximum 3000; pneumatic motor or actuator supplied with valve.

The V-3000 Pneumatic Actuator from Johnson Controls Industries Inc. is a 3-way pneumatic actuator that provides a maximum flush force of 25 lbs, and a spring force to close of 3.7 lbs. The upper rod has an outside diameter of 0.757" while the lower rod has an inside diameter of 0.593". This actuator was designed for use on pneumatic panels with the NEMA configuration of 4X or 4XB.

Open your door to the world of pneumatic valves with this V-3000 3 to 13 PSI pneumatic valve actuator. Its spring-loaded design has a 25 pound maximum load, making it great for pneumatic control output. It features a compact design, making it great for placing in small spaces. Welcome to the Johnson Controls family.

The Johnson Controls V3000 pneumatic valve actuator, 3 to 13 spring, 3"" wide is a component of automated systems that require air to control valves. Pneumatic valve actuators operate by converting air pressure from a pneumatic source into mechanical energy, which rotates the shaft of the device and opens or closes the valve. The size of this electrical actuator is 8" wide x 8" long x 5" high.

The Johnson Controls V-3000-8012 pneumatic valve actuator allows you to control the pneumatic valves in your HVAC system. The valve has a maximum pressure of 25 psi, and can be used for both springs 3 through 13.

V3000 Series Pneumatic Actuator - Pneumatic valve actuator, screw-in mounting, forward/reverse, with 3 to 13 pneumatic spring, aluminum body and cap, cast iron actuator

Our Johnson Controls V-3000-8012 Pneumatic Valve Actuator, 3 to 13 Spring can be used on just about anything that requires pumping or activation. With an impact type head, it is up to the task of even the most extreme conditions. It's got a minimum operating pressure of 0.5 PSI and a maximum pressure of 250 PSI. it has a stroke of 1 inch and a max port size of 1/8".

From Johnson Controls, the V-3000 Series is a pneumatic valve actuator capable of switching high load, multi-turn valves. This 2-position pneumatic actuator provides 25 pounds to open the valve and 15 pounds to hold it open. The low spring force allows for longer valve life and reduced maintenance. The V-3000 Series has two output variations: normally open (NO) and normally closed (NC). The devices are designed with hand actuation or hand actuation with an auxiliary power source.

Pneumatic spring actuators convert manual pressure into a proportional linear or rotary motion. A mechanical spring provides the power to position a load over a wide range of strokes and hold it there until released. These pneumatic spring actuators have a maximum operating speed of 8" per second.

The V-3000 series valves are 2-way, 3 position non-adjustable pneumatic valves capable of working in extreme temperature environments. Features include a stainless steel body with stainless steel pneumatic actuator. Also includes a high temperature polypropylene disc stem, high temperature ball seat, stainless steel poppet, aluminum alloy valve plug plate/base plate, and external adjustment screws.

Experienced design professionals currently use pneumatically controlled valves for a variety of purposes, but have been limited to fairly small valves. The difficulty has been in properly sensing the pressure changes necessary to control the larger valves.

The Actuator used to drive the on-off function on a variety of ventilating systems. This actuator is used with a brush cap and is useful in situations where space is limited, and/or it is necessary to position the valve in close proximity to the load or control device.