Apex
APEX 071-TX-5418 13287 SCKT 1/2 FMALE SQ
13287 SCKT 1/2 FMALE SQApex 071-M-6MM11 06901 SCKT 1/4 FMALE SQAPEX 071-M-6MM11 06901 SCKT 1/4 FMALE SQ06901, SCKT 1/4 FMALE SQ06901 SCKT 1/4 FMALE SQ071-M-6MM11 06901 SCKT 1/4 FMALE SQThe Apex...
My Account
If you are already registered, please log in.
Create your account and enjoy a new shopping experience.
Create A New Account29002 SCKT 1/2 FMALE SQ
This sponge is designed to replace the iron stand sponge
The sponge can be used dry or soaked in water
This sponge replacement for iron stands has no holes so you can clean the tips of your soldering irons without worrying about the sponge falling apart
The Apex Weller Solder Tip Cleaning Sponge with Slits is perfect for removing flux residue and cleaning the inner walls of your Weller soldering iron
This cleaning sponge has been designed to fit the Apex WELTC205 Weller Solder Tip Cleaning Stand
With no holes, this sponge will not damage or corrode the iron stand
It has no holes in it and is used to store soldering Irons and tips when not in use
Our WELTC205 Weller Solder Tip Cleaning Sponge with Slits measures 5/8" x 2-5/8" x 2-3/4"
The slits hold the wire iron while soldering and the slots clean the tip of the hot iron after soldering
When you are soldering a lot, one of your biggest challenges is to clean the tip regularly
The Apex® WELTC205 Weller Solder Tip Cleaning Sponge with Slits is a sponge replacement for iron stands
The sponge is a direct replacement for the iron stand, and will not scratch or mar your tip or soldering iron
This 2-ply, 2-layer sponge is bonded with slits on one side and slots on the opposite side
You can clean your tip three times longer before it needs replacing
Each sponge has been slit diagonally to fit around any size tip, allowing you to achieve a consistent and thorough clean
This sponge has slits that allow you to connect it to the iron stand (WELTC203 or WELTC204) so that you do not need an iron holder
It is made from a cellulose-type material designed to resist breakdown by acids, alkalis and solvents found in fluxes
BK112631) that have no holes
This sponge is five inches square and has slits on one side to allow it to be used in place of solder sponges in Weller (sold separately) iron stands
This sponge is a replacement for the iron stand that comes with Weller Solder Tip Cleaning Iron WELTC205
The iron does not come with this mini sponge, but when attached to the iron this small sponge will absorb the solder and you can easily remove it from the tool
It's pre-cut and will fit the Weller TC100 iron stand
Cleaning sponge with slits, 2-5/8" x 2-5/8 x 5/8" Solder Tip Cleaning Sponge with Slits, 2-5/8" x 2-5/8 x 5/8"
The C205 Weller Solder Tip Cleaning Sponge is made out of sponge material with slits in it and can be used to replace your iron stand sponge
The design of the sponge swells up when heated from the soldering iron, providing a larger surface area for cleaning
Replacement for iron stands (ex
The Solder Tip Cleaning Sponge with Slits is made in the USA from platinum-cured silicone
~~The WELTC205: Weller Solder Tip Cleaning Sponge has a non-abrasive surface that cleans iron and nickel tip solder residues with little or no damage to the iron stand
It is necessary to replace the sponge every once in a while because it wears down
Keep your tips clean and ready to use with this Solder Tip Cleaning Sponge with Slits