MARS 33267 240V 1SPDT 3N/O Sequencer

240V 1SPDT 3N/O Sequencer

The 240V 1SPDT 3N/O Sequencer, Item No. 33267, is a non-dimming duty cycle switching unit with both N and O connections. This SPST switch has an easy to read red indicator arm and operates at 120 VAC. Its duty cycle is rated at 20%.

The 33267 240V 1SPDT 3N/O Sequencer by Mars Electric is a heavy-duty, 230-volt device that is used in 230-volt applications to control when three relay outputs can be energized and de-energized. Each output provides 0.5 amps at 30 volts.

The MARS 33267 240V 1SPDT 3N/O Sequencer is used for switching power on and off to 3 N/O loads when attached to a MARS Panel. The 33267 has the ability to switch at 120V or 240V. It can be used in applications with multiple start-ups and shutdowns in a day by utilizing the "C" terminal to switch between output extensions of the individual loads.

The MARS 33267 240V 1SPDT 3N/O Sequencer works with traditional and dual voltage electric water heaters. It controls the on and off of the water heater elements and provides a delay in heating to prevent element fatigue and failure.

The MARS 240V 1SPDT 3N/O Sequencer features 3 No Load (open) relay contacts, and one Common (Load) terminal. The relay coils are rated for 30 volts at 20mA. This allows you to interface a typical 120VAC appliance to a normally open contact, and the common load contact to a normally closed contact. All of these contacts can be controlled via a 3 position toggle switch wired in series with the common load terminal along with a NO/NC circuit.

The MARS-33267 240V 1SPDT 3NO Sequencer allows you to operate up to four devices from one power supply. With this product, any number of lights can be turned on or off at the same time without causing damage to your equipment.

The Mars 33267 is a 15 Amp, 240V, Single Pole Double Throw (SPDT) 3N/O sequencer that works with Many other electrical devices and can even function as a continuously variable device. It is supplied with a 1Amp auxiliary contact to provide the ability to control two (2) separate and independent circuits and it comes with Five (5) #6 terminal screws for simple and secure installation. The Mars 33267 can be installed in or outdoors and it comes with an easy to follow instruction manual. Because of its strong metal construction, this sequencer is capable of operating in harsh conditions such as

MARS Electric's new 1-Space 3-Wire to Ground, Class B DPST-NO high voltage disconnect switches come in a variety of voltages and amperage ratings to meet all of your electricians needs.

When connected to your pool's electrical system, this product will work with the other components in the Master Control System (MCS) to provide control for multiple pumps, filter systems, heaters and other water features. It controls up to three 3-phase (120V) devices, whether pumps or controls; or any combination of individual single-phase (120/240V), 3-phase (120V) or 240V devices, such as pumps and controls. This sequencer is intended for use with 120V single-phase lighting loads only.

MARS Brand Vacuum Controller, Amp Range 5-30, Number of Poles 3, Switching Device Type DPST, Application Control of Induction or Solid State Motors or other AC Motor Control Applications Where Multiple Position Control is Needed in One Enclosure, Vacuum Capacitor Start Compatible, Panel Mounting.

The "MARS" is a one-way normally open, three selector, three position switch with stop. The selector moves only in the ON position. The contacts are rated at 20A @240VAC. The selector is pinned to the appropriate contact with .060 male pins. Each contact has .187 male terminals accepting wire gauge sizes 20-14 AWG.

The MARS 33267 is an electronic switch capable of controlling three Porcelain Enameled (PE) light sockets with on/off switching. The MARS 33267 may be operated via the front panel push buttons, or by 3 wire (2 hot legs and neutral) control connections.