Warrick-Gems Sensors & Controls 26MB1A0 10K 120V 11 PIN LWCO

10K 120V 11 PIN LWCO

With 26MB1A0 10K 120V 11 PIN LWCO sensor available now from Warrick-Gems Sensors & Controls, you can find many applications for it. This sensor is part of the Automation category, which you can see more other products from below including sensor, wirdl, pcb board and much more.

This 26MB1A0 10K 120V 11 PIN LWCO from Warrick-Gems Sensors & Controls is a 11 pin micro-birthing device that features a latching tower and includes seal. This sensor has a voltage of 120 and a control voltage of 10k, and comes with four wire leads (5 ft. lon), 4-.065 in. (113 mm) plated slip nuts and washers, and two .188 in. (4.78 mm) nylon locknuts. It's for use with .056 in., .187 in., and .250 in.

The Warrick-Gems Sensors and Controls 26MB1A0 10K 120V 11 PIN LWCO is a type of power supply and it has two inputs and ten outputs. It has a input voltage of zero to nine volts and a current of .055 amps and a frequency of zero to 50 hertz. This one package comes with everything that you need, including the instructions, the box, the part itself, five wires, and some straps. Just connect it to any ten 20 milliamp power supplies such as motion sensors or relays.

The Sensors & Controls 26MB1A0 10K 120V 11 PIN LWCO with Liquid-filled Gauge is a high quality product for generating process signals, with an accuracy of 0.3% of the span. The Liquid filled gauge reduces vibration and noise, so you can monitor performance in noisy environments. This product has a Positive Lock overrange protection to prevent damage to the sensing element due to overloads. It also comes with a minimum of 10 calibrations per year, for no extra charge.

Sensors and Controls 26MB1A0 10K 120V 11 PIN LWCO [OLD PN : 26MB1A0, LW2-10K120V, LWCO], DELL PE1911 BATCH NO.: 40L8730, FUJITSU FY22ATSR PIN: 29L3322, IBM - DELL PE1911 x12 9MM LAMINATED-WIRING CHART CARD CABLE, DELL - HP A9Z5K908-741 x9 11MM LAMINATED-WIRING CHART CARD C

This Sensors & Controls 26MB1A0 part is a 10K ohm 120V 11 PIN LWCO manufactured by Warrick-Gems.

The LWCO (limit switch connector assembly) 10K 120V 11PIN has been designed for use in environments where safety and reliability are of the utmost concern. Protection is afforded to personnel by disconnecting motor windings/components when a hazardous condition occurs. The brake terminates the circuit to the protected component, but does not interrupt power to the motor windings or other electrical loads.

The 26MB1A0 is a 10K/120V General Purpose Lead Wire, designed for installation applications such as detection and signaling devices. The sensor has an 11-pin lead wire connector with standard pin configuration and comes in a 2 foot length. This rugged, full metal jacket sensor is made of 14 gauge stainless steel and brass. It is suitable for elevated temperature indoor or outdoor installations.

Warrick-Gems 26MB1A0 Sensors and Controls Inserts are used on Wick type low water cut-off devices that have a 11 pin bayonet base with two wires. The connectors have a 3/8? O.D. cable clamp and comes with a 5/16? x 1-1/4? tapered barrel connector, 10' ft braided cable, and a ruggedized barrel socket for continuous use at 120 VAC nominal, at 50/60 Hz.

For industries with electrically conductive liquids, the 26MB1A0 is a single-ended 10k Ohm NTC with a 120V bias and a 11-pin bayonetablet connector. Built-in over-temperature protection with an automatic reset makes sure your liquid level control is safe even when it’s on long hours. This liquid level control is housed in a compact aluminum housing for increased durability and has a large 5/8” (16 mm) diameter dial making it easy to adjust.

Kee Klamp® is a leading U.S. manufacturer and distributor of structural and specialty pipe and fittings for use in building and plumbing applications. Kee Klamp® manufactures and distributes tens of thousands of commercial products, including trunk lines, MDPE piping, sprinkler piping, curb adaptors, joints and fittings, fire-sprinkler piping systems, hydrants and valves, chemical specialties such as corrugated PVC water pipe and injection molded polymer distribution pipes for De-Icing applications.