Dwyer Instruments A-302 Dwyer Stainless Steel Static Pressure Tip for 3/16" and 1/8" ID Plastic Tubing

"3/16""&1/8""I.D.Static # Tip"

The Dwyer Instruments A-302 "3/16""&1/8""I.D.Static # Tip" is a replacement tip for either the Dwyer Instruments 1173-Propane Detector Gauge and 1270 Propane Detector Alarm, or the Dwyer Instruments 1173-Natural Gas Detector Gauge and 1270 Natural Gas Detector Alarm. This tip will fit snugly into any 3/16"" or 1/8"" (4 mm) ID plastic tubing and can be used to conduct measurement values such as air pressure changes, liquid levels, temperatures of both heating and cooling

When you need a more rigid tube for those hard to reach places, the Dwyer Instruments A302-3/16""&1/8""I.D.Static # Tip is a great option. Made from stainless steel, the Dwyer Instruments A302-3/16""&1/8""I.D.Static # Tip will resist corrosion and maintain its form after multiple uses. Make sure you're using this tip on a low-pressure gauge and tubing and that you're not squeezing or obstructing air movement with your tubing before you go ahead and use this tip to get an accurate reading of your

This style of Dwyer Instruments plastic tubing fitting features a stainless steel construction with a 3/16""&1/8""I.D.Static connection tabs so you can easily add incoming pressure on a wind advisory or storm event. These tips are especially handy when working with wood frame homes to add incoming low pressure on one point of the house, and use high pressure on another to find potential leaks in your specific home. This plastic Dwyer Instruments nylon tubing fitting is 1" long and is recommended for a 1/8"I.D. polyurethane or polyvinyl chloride tubing that features a solid PVC

The Dwyer Instruments A-302 Stainless Steel Static Pressure Tip for 3/16" and 1/8" ID Plastic Tubing is a static pressure gauge which easily attaches to a 3/16"" or 1/8"" plastic tubing. This gauge is a must have for a variety of industrial processes, especially when your work requires the gathering of air flow information.

Dwyer instruments stainless steel static pressure tip for 3/16" and 1/8" id plastic tubing.

The A302 Dwyer Instruments Static Pressure Tip for 3/16" and 1/8" ID Tubing is an accessory for the 3000 series barometers, thermometers and hygrometers. It is used in the lower (trend) side of the unit when attaching directly to a plastic tubing. The tip is made of stainless steel and is pointed at both ends."

The A302 Static Tip is to be used with 3/16" and 1/8" inside diameter plastic tubing.

The Dwyer Instruments A-302 Stainless Steel Static Pressure Tip is designed for use with plastic tubing to measure static pressure in 3/16" and 1/8" inner diameters. The Snaptite FIP threads allow the tip to be easily engaged to the tubing.

The Dwyer Instruments A-302 stainless steel static pressure tip (for 3/16" and 1/8" ID plastic tubing) is used to measure the static pressure of gases indirectly using a Bourdon tube manometer. This allows you to measure the gain or loss in static pressure of gases, above atmospheric, without having to block off the gas line.

If you are looking to save money while replacing disposable plastic tubing, this Dwyer Instruments tip is a great solution. It can be attached to both 3/16" and 1/8" I.D. plastic tubing using the included stainless steel clamp wrench. The tip has an observation port for placing a sampling tube in order to collect water samples. This stainless steel tip is corrosion-resistant and built to last.

This static pressure gauge is designed for use with 3/16'' and 1/8'' i.d. plastic tubing, which can be connected directly to the transmitter using a universal port connector. The stainless steel body is resistant to welding, grinding, heat, chemicals, and solvents common in high-pressure systems. Use it to monitor static pressure on spraying equipment or air conditioners, temperature control equipment, blowdown lines, cooling towers, refrigeration condensers, filtration systems, soft-drink equipment.

The 303 stainless steel tip is used to measure static pressure in hoses. It is designed for hoses with IDs of 3/16" or 1/8". The standard 0-20 psig taper ranges are engraved on the top of the cups to ensure accurate readings at various pressures.