JOHNSON CONTROLS 321482

REMOTE BULB TEMP CONTROLLER SPST OPEN HIGH 100-240

The 321482 Remote Bulb Temp Controller allows a remote light to be installed in a convenient indoor location and the bulb controlled from an outlet. The controller replaces a standard wall switch and can control a 120 volt incandescent lamp, neon lamp, or florescent lamp from 80 to 360 watts. This UL listed controller has an SPST open high switch for controlling incandescent bulbs.

The Remote Bulb Temp Controller (321482) can be used to remotely control lamps or other loads which run off 120 VAC. The controller has an input voltage range of 100 to 240 VAC and will work on all types of loads including resistive, inductive,and capacitive. The output is SPST open-collector (12 VDC) with an internal pull-up resistor (Typical 1015 Ohms).

The 321482 is a remote bulb temp controller; spst; on-off; external pilot type (compatible with pilot of 321381 or pilot of 321483); pilot operates 250vac; 100-240 vac; single-channel; 16-ft. cord length; controls outdoor lighting equipment; requires 3/4 in. x 10 ft. thermocouple, sold separately (screw into light socket); adjustable thermostat controls bulb temperature

Remote bulb used for HFC lamps. This model is a SPST open high voltage. Voltage range for this controller is 100-240VAC. Bulb terminal to terminal distance is 5cm, the lamp current range is 0.5A to 3A.

The Remote Bulb Temp Controller is designed for use with high-intensity discharge (HID) instruments that employ an arc-tube ballast. For optimal performance, the controller should be used with bulbs having a forward voltage of 20 - 180 VDC. The controller provides sine wave current to lamps approximating a normal line voltage sine wave shape at the lamp terminals by means of phase displacement. The phase shift is accomplished by modulating the phase angle of input current entering the ballast. The controller regulates the operating temperature of the lamp by adjusting both the minimum phase angle and minimum lamp voltage, which are programmed via dip

Apply Johnson Controls 321482 Remote Bulb Temp Controller to your light and you can then adjust the temperature of that light from a great distance away: up to 1000 feet. This device has an outdoor rating and is ideal for garages, porches, barns and other areas you want to protect but want to be able to control your lighting from a distance.

The Johnson Controls 321482 Remote Bulb Temp Controller is an SPST-NO on-off switch control with a 5 amp rating. It can handle many loads up to 100 watts. It has a black plastic body with an aluminum faceplate and has a diode for reverse voltage protection.

Johnson Controls 321482, Remote Lamp/Appliance Controller, For use with a variety of electronic ballasts to control on/off or dimming of lighting devices remotely from a panel, wall box or individual switch without field wiring, SPST power contacts rated 16A at 120V 5-24VDC Max load on ON portion of contacts is 8.0 amps @ 120VAC Max load on OFF portion of contacts is 3.2 amps @ 120VAC Max load on DIM portion of contacts is 7.0 amps @ 120VAC Max switching current IL rated 10 amps @ 120VAC, 25

A remote bulb temperature controller, for use with T8 fluorescent lamps. The device controls the current supplied to the lamp. This is achieved via adjustment of the voltage applied across the lamp electrodes within narrow limits. The resultant extent of lamp-current modulation is sensed and compared with a reference voltage level. The comparison signal is used to control an output transistor which regulates the voltage at the lamp electrodes.

Simply wire this bulb temperature controller into any household florescent light fixture and control the ambient temperature of your Enviro Chamber or Terrarium. This product will work on florescent tubes up to 4 feet in length.

Experience the benefits of remote control—enhanced convenience, greater energy efficiency, and added safety. Installation is simple, too. Connect the controller to 2-wire branch circuit wiring by using a three-wire adapter with built-in terminal blocks. Film-faced thermostat overcoats stick over both terminals. Then install the controller by running conductor wire from source to remote control meeting code requirements for wiring devices with established polarity (ex: copper for hot wire).

Johnson Controls 321482, Model # 16P228. This temperature controller is a floor model and was used to control a fan in a dust collector. The controller has been checked, cleaned and calibrated.