Johnson Controls P545NCB-25 ElecLubeOil 90sec L/O 10# ElecLubeOil 90sec L/O 10#

ElecLubeOil 90sec L/O 10#

ElecLubeOil 90sec L/O 10# is used to lubricate power supply contacts on electrical equipment during warm-up, within the oil fill period of the equipment. The resulting electrostatic charge protects against dust and particulate matter entering the equipment. This new formulation results in substantial improvements in both product performance and environmental friendliness.

If you're in the market for a compact, rugged, and reliable electric heat exchanger, look no further than the P545NCB-25 ElecLubeOil 90sec L/O 10#. Fully tested to your complete satisfaction with an unsurpassed 5 year warranty.

P545NCB-25 ElecLubeOil 90sec L/O 10#

The P545NCB ElecLubeOil 90sec L/O 10# System uses PTFE/silicone technology in the pump to deliver an electrically insulating, long-life lubricant in 90 seconds. This system is designed for use in applications where the lubricant is not exposed to high temperatures or extreme pressures.

Built for ease of use, Johnson Controls' P545NCB-25 ElecLubeOil 90sec L/O 10# gives you the simplicity you need while maintaining very high levels of reliability. You can run one or more Multi-Tray Pro II timers to automatically mix oil and energy-efficient fluids to conserve up to 30 percent more fluid than with any other timer. The higher precision flowmeters give you up to 0.01 percent accuracy and an intuitive hold-metered feature that lets you maintain calibration and avoid repairs and downtime. It's easy to read flowmeters and timers, and the T

A highly effective lubricant that is recommended for the cleanest, most economical operation of all conventional electric motors. Lubricates cavitation-proof for 90 seconds, providing ample time to make adjustments during start-up (lubrication points above base gasket) and is tolerant of cavitation. May be used in any type of gearcase or reduction gearbox where clearances are wide enough to minimize oil carry-over. This product contains no bactericides.

JCI Corded Trolley - TLS-25 Portable Blower The perfect multi-purpose trolley ideal for oil maintenance of wood chips, bark, grindings and pellets combusted by pellet stoves. It has 2 speeds which combined with its blow volume of 3150 cu.ft./min. The trolley also features an inline 10 lbs. oil tank with 90 seconds of oil in 90 seconds out delivery capability.

Lube oil, lubricating oil for electric motors. Protects motor from wear. Reduces stress, heating, and noise. Meets or exceeds ANSI/MIL-L-4360D. 20 quarts per can.

The P545N and P540N features a unique in-line design and capillary tube oiler to offer the fastest light off in the market today. The system delivers oil to the burner in 90 seconds or less. It is helpful for troubleshooting problems with slow lighting and when servicing the line set. The in-line design allows for easy access to all parts of the piping and couplers. Includes 15 cc non contaminating syringe, capillary tube and filter wrench.

This ONE-SPEED automatic lubrication system is the only 100% automatic system of its kind in North America. Its compact design ensures ease of operation and reduced oil consumption. Microprocessor controlled operator interface allows for specific setting of tank size, oil volume/type, and average cycles per hour. The fully integrated device can be plumbed to a system with a manual controlled pump or tank fill valve. Ideal for yard concrete mixers, cement trucks, asphalt pavers, landscaping machines and similar equipment where engine cranking creates dust or exposure to dirt or water that may inhibit proper lubrication. Real time display screen shows

Ideal for small to mid-sized pump applications where longer change intervals are acceptable, P545NCB-25 has a high viscosity grade (> 18 SUS @100F), good thermal stability, and excellent shear stability. It also contains 23% more solvent than P515NCO-25 formulation to enhance tool clean up.

Aeration systems are used whenever the product is heated to the point where vapor bubbles form. Vapor bubbles nucleate on product or pipe surfaces and grow to a size large enough for liquids to boil. This cycle repeats many times during the process which requires energy input to maintain efficient operation. The use of non-ionic surfactant based bubblepoint lowering agents has been recognized as an effective alternative to cooling tower water or expense of electricity for controlling vapor bubbles in aerated tanks.