ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button

CAD CELL RELAY (45 SEC)INTERMITTENT

ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button is a cell relay (45 sec) intermittent ignition. It can be used as safety switch for solid-state relay coils. It has the following terminals: NO, NC + PUSH TO RESET, and NO and normally open (N/O). The ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button also has a flame sensing input and safety switch input. If you need more specifications please call our

This 45-second ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button is a CELL RELAY. The same technology used in the space shuttle and NASA space probes works for your home too! This unit can be used to control lighting and heating, motorize gates and garage doors, and much more. It is worth noting that this ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button does not require a neutral wire when installing. It also has

The ICM Controls 113232 oil primary, intermittent ignition, flame sensing circuit, 45 sec, safety switch, reset button has a continuous current rating of 3.0 A and a working voltage of 24 VAC or DC - but what does that mean? If your relays are running hot because of the loads you are putting on them an ICM Controls 113232 oil primary, intermittent ignition, flame sensing circuit, 45 sec, safety switch, reset button may be your answer. Its operating temperature is 12°C to 46°C and its rated current at 10 mm lead length is 1.2 A to a maximum of

ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button APPLICATION:For oil burner flame ignition. ICM Controls 113232 FAN RELAY is used in most oil-fired boilers to control High Temperature Limit (HTR) and Low Temperature Limit (LTR) thermostatic electric fans. Switch function is Intermittent.

ICM Controls 113232 Oil Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec, Safety Switch, Reset Button is part of the Simer range from ICM Controls. Simer provides a wide range of safety relays and safety electronic switches for a variety of applications. All products are designed and tested to meet to CE mark standards and international approvals where applicable.

The ICM Controls 113232 Oil Drain Primary, Intermittent Ignition, Flame Sensing Circuit, 45 Sec. Safety Switch, Reset Button is a primary and secondary oil primary with 45 second time delay and flame sensing circuit. It can be installed to monitor burner ignition and cut-off along with the oil level in the tank. This control lasts for over one million cycles and provides electronic reliability that will allow you to secure high maintenance tasks both day or night.

The ICM Controls 113232 is a flame sensing circuit, 45 sec ignition and safety switch, reset button. It is made of aluminum and brass and is equipped with stainless steel terminals. It is applicable for the furnace, water heater or oven.

Oil primary equipment is used to ignite the fuel flow sensing system. This particular oil-based relay is designed with a 0.5 second to 45 second delay before it opens the main fuel valve circuit; which flows the oil vapors through the flame detection sensor, which removes the flame, and then allows air into the valve, closing off the fuel-gas pressure connection. This arrangement helps keep unwanted unwanted gas fumes out of the pipeline. It can be mounted on a pipe or support system that is fitted with mounting bracket; this ICM Oil Primary equipment comes with 3/4" female NPT threaded connections for connection to gas

We are an industrial automation products supplier in Shenzhen China. Our products include industrial automation products, industrial computer peripherals, industrial communication Cables, industrial automation control devices, CNC routers/CNC milling machines/3D printers/automatic inspection machines/industrial robots. We dedicate our enterprise success to the product quality and service.

A flame sensor alarm system transmits a current signal to an oil primary controller, which has a built-in safety switch. The safety switch controls oil flow to the burner. If the flame is not present, the safety switch turns off the oil primary and then turns it on again after a preset delay of 45 seconds. The controller holds the burner on until the detector senses flame again. Fault protection is provided by an integral time-delay relay that shuts down the entire circuit if there is no flame signal for any period longer than 20 seconds or if either sensor is shorted or grounded.

The ICM Controls 113232 Oil Primary , Intermittent Ignition, Flame Sensing Circuit with Safety Switch, Reset Button is an ideal replacement for most furnace manufacturers.

The ICM Controls 113232 Oil Primary Intermittent Ignition Flame Sensing